ZNIM
Thermal grease applied at a precision electronic interface

Thermal Grease for Stable Heat Transfer Across Precision Interfaces

Low-viscosity silicone grease fills microscopic air gaps between heat-generating components and heat sinks, reducing contact thermal resistance for power electronics, automotive charging, and high-frequency communication modules.

Home chevron_right Product Center chevron_right Thermal Grease

Reduce Microscopic Air Gaps and Build a More Complete Thermal Path

Even machined metal surfaces leave microscopic voids that trap air and raise interface resistance. ZNIM thermal grease wets mating surfaces, forms an ultra-thin bond line, and keeps heat flowing under sustained load—without curing complexity of multi-part systems.

Low Thermal Resistance

Thin BLT and strong surface wetting minimize contact resistance for efficient heat transfer.

Easy to Apply

Compatible with screen/stencil printing and automated or manual syringe dispensing.

Micro-Gap Filling

Fills microscopic voids at the component–heat-sink interface for a more complete thermal path.

High Reliability

Stable under long-term high temperature with low dry-out risk when applied and stored per TDS.

Thermal Grease Series Overview

Compare TIG grades by conductivity, resistance, bond-line thickness, and viscosity. Download the product datasheets for test methods and storage guidance.

Image Model Color Thermal Conductivity
(W/m·K)
Thermal Resistance
@40 psi (°C·cm²/W)
BLT
(μm)
Viscosity
@1 s⁻¹ (Pa·s)
Density
(g/cm³)
Operating Temp
(°C)
Actions
TIG0350C product image
TIG0350C Blue 3.5 0.13 25 350 3.30 −40 to 150
TIG0350LV product image
TIG0350LV Light Gray 3.5 0.125 35 250 3.10 −40 to 150
TIG0600E product image
TIG0600E Gray 6.0 0.068 25 380 2.60 −40 to 150
TIG0601 product image
TIG0601 Gray 6.0 0.088 30 620 3.30 −40 to 150
TIG0700 product image
TIG0700 Gray 7.0 0.12 48 390 3.08 −40 to 150

Where Thermal Grease is the Better Choice

  • Ultra-thin bond lines where pre-cut pads add excess thickness or stack-up risk.
  • CPU/GPU and power-module interfaces that need maximum surface wetting.
  • Screen/stencil printing or syringe dispensing on high-volume lines.
  • Reworkable assemblies that do not require a cured elastomer structure.
  • Applications targeting −40 to 150 °C with stable long-term thermal performance.
Thermal grease applied on a CPU/GPU heat-transfer interface

Stable Application Starts With Controlled Printing and Dispensing

Prepare the surface, apply a controlled film, assemble under proper pressure, then verify bond-line thickness and coverage.

01

Surface Clean

Remove oil, dust, and residues from both mating surfaces before coating.

02

Apply Grease

Screen/stencil print or dispense a uniform film matched to the target BLT.

03

Assemble

Mount the heat sink or mating part with controlled pressure to wet the interface.

04

Verify

Check thickness, coverage, and squeeze-out; adjust process against the grade TDS.

Typical Application Locations

From computing heat sinks to telecom RRU/BBU and automotive power electronics.

CPU and GPU heat sink interface

CPU / GPU Heat Sinks

Laptop, desktop, and accelerator packages requiring thin BLT and low resistance.

Automotive ADAS and power electronics module

ADAS Power Modules

Controller and sensor cooling in intelligent driving systems.

5G base station telecom equipment

5G Base Station RRU/BBU

High-density RF and baseband boards in outdoor and indoor telecom gear.

Industrial power supply and conversion module

Power Supplies & Controllers

Power conversion, industrial control, and high-heat semiconductor packages.

Frequently Asked Questions

Need a grease formulation for a specific interface?

Request a Consultation